All Products

Male DC Power Jack push button 2 Pin Terminal -5.5x2.1MMMale dc to terminal block adapter is made for special industrial application, for connecting single wires with open cable heads. It also may be used inside the interest vicinity for example for version railroading. Therefore you may join numero..

MAX232 dual driver & receiverThe MAX232 by Maxim Integrated Circuits converts signals from an RS-232 serial port to signals suitable for use in compatible digital logic circuits. The MAX232 is a dual driver/receiver and typically converts the RX, TX, CTS and RTS signals. The drivers provide RS-232 v..

MAX485 - RS-485/RS-422 Transceiver ICThe MAX485 is low-power transceivers for RS-485 and RS- 422 communication. The IC contains one driver and one receiver. The driver slew rates of the MAX485 is not limited, allowing them to transmit up to 2.5Mbps. These transceivers draw between 120µA and 500µA of..

MAX7219 8x8 LED Dot Matrix Display Module For ArduinoHey guys, if you want to think to add some cool animation or scrolling text to your DIY project, or as an individual project, which contains a lot of LEDs, the MAX7219 Dot Led Matrix Module will help you better.This module is the collection of 64 ..

MCP6004-Quad General Purpose Op AmpThe MCP6004 is a quad general purpose op amp offering rail-to-rail input and output over the 1.8 to 6V operating range. This amplifier has a typical GBWP of 1 MHz with typical quiescent current of 100 microamperes. The MCP6004 is available in 14-lead PDIP, SOIC and..

MCT2E - Phototransistor OptocouplerStandard Single Channel Phototransistor Couplers With Base Connection. The MCT2/ MCTE family is an Industry Standard Single Channel Phototransistor.General purpose optocoupler with TTL compatibility, Provides High Voltage Electrical Isolation 3.55kV. Good response ..

This is an Electronic DIY KIT, some soldering experience is required.  The PCB (Printed Circuit Board) is provided with the DIY KIT and it needs to be soldered, hence the name DIY KIT.  All required electronic parts are provided.Working voltage : 3-5V DC Dimension : 66 X 61 MM Max detector distance ..

Metal Oxide Varistor (MOV)-14D471K Radial Lead Resin Coated Metal Oxide Varistor for Surge Protection.Specifications:Part No-14D471KMaximum Allowable Voltage ACrms(V)-300Maximum Allowable Voltage DC(V)-385Maximum Allowable Voltage Max-423Varistor Voltage (@1mA) Vb(Vdc)-470Varistor Voltage (@1mA) Max..

MFRC 522 RFID Card Reader Module - 13.56MhzMifare RC522 is the high integrated RFID card reader which works on non-contact 13.56 MHz communication, is designed by NXP as a low power consumption, low cost and compact size read and write chip, is the best choice in the development of smart meters and ..

Micro Pen Soldering Iron BitThis is a replacement soldering tip for Soldering Iron. This is a conical type of soldering tip, and is the same version that originally comes with the soldering iron. Replacing the tip is very easy - simple unscrew the shield, slip the replacement tip in, and screw the..

Pocket card LED lampCondition: NewThis card has 3 lights, double-sided USB designMini LED night light, for camping, desktop lighting0.2W low output,2835 chips led, long lighting5000mah mobile power supply, support 100 hours lightingEasy to carry, just, hang it on your keychain or put in your wallet..

The MOC3021 is optically isolated triac driver device.It is designed for interfacing low voltage electronic components and triacs to control resistive and inductive loads.Features400 V Phototriac Driver OutputGallium-Arsenide-Diode Infrared Source and Optically-Coupled Silicon Traic Driver (Bilatera..