Any order between 12-10-2017 to 1-11-2017 will be shipped at 2-11-2017
If you not find your right product!      Write us email at   sales@component7.com.

SPI to Ethernet Adapter (ENC28J60 Ethernet Module)

SPI to Ethernet Adapter (ENC28J60 Ethernet Module)

SPI to Ethernet Adapter (ENC28J60 Ethernet Module)

This module contains what you need to enable ethernet on your next microcontroller project. This board utilizes the new Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20 MHz.

It includes a ENC28J60 ethernet controller, an RJ45 socket with link/activity lights and integrated transformer. This ethernet module enables you to connect a particular Embedded device (equipped with SPI support) on to a network. By using this Ethernet module (along with a microcontroller running a small TCP/IP stack) applications like Embedded Web server can be easily developed.

Use this module to enable Ethernet interface for your product. It works with any microcontroller operating at 3.3V or 5V. This module works at 5V and is compatible with 5V interface lines. Use SPI process to interface with it. Host web server, ping the module or add it to home automation via internet. Heart of this module is ENC28J60 Ethernet controller from Microchip.

Use of RJ45 with Integrated transformer has made it possible to reduce the size of board. This board is assembled with all components as shown in the pictures below. The circuit board includes all required components for the ethernet controller, plus a 3.3V Voltage Regulator and a RJ-45 jack with integrated transformer and built-in Link and Activity LEDs for connection to an Ethernet Local Area Network.

Features

  • Microchip ENC28J60 Ethernet Chip supporting Microchip’s TCP/IP protocol stack, with IPv4, UDP, TCP, DHCP, ICMP, FTP, and HTTP support
  • On board voltage regulator for 3V generation, so board operates on 5V
  • Compatible with all controllers having an SPI interface, SPI interface takes only few pins to add Ethernet interface to your microcontroller project
  •  Suitable for Either 5V or 3.3V Interface
  • LAN connector with build in transformer
  • Link and Activity LED's on Ethernet connector
  • 8 pin standard interface connector with spacing of 0.1” (2.54 mm) row pins
  • IEEE 802.3 Compatible with Integrated MAC and 10Base-T PHY
  • Fully Compatible with 10/100/1000Base-T Networks
  • Supports One 10Base-T Port with Automatic Polarity Detection and Correction
  • Supports Full and Half-Duplex modes
  • Programmable Automatic Retransmit on Collision
  • Programmable Padding and CRC Generation
  • Programmable SPI Interface with Clock Speeds Up to 20 MHz

Applications

  • Remote control and monitoring
  • Data capture and logging
  • Industrial Automation
  • Building Automation
  • Appliance remote management
  • Robotics
  • Microcontroller Research and Development
  • TCP/IP Research and Development

Specification

  • Board Size: 68x22mm
  • Operating Voltage: +5V DC
  • Current Consumption: 180mA average
  • Pin Spacing: 0.1" (2.54mm)

Write a review

Note: HTML is not translated!
    Bad           Good

  • Views: 815
  • Product Code: SPI to Ethernet Adapter (ENC28J60 Ethernet Module)
  • Availability: In Stock
  • Rs550.00

Tags: spi, ethernet, adapter, enc28j60, ethernet, module, spi to ethernet, communication, robot, kit

RJ45 Shielded network socketEthernet portCrystal humpback 8PinLong TypeCopper..
Rs45.00

A resistor is a passive two-terminal electrical component that implements electrical resistance as a..
Rs1.00